Wednesday, August 24, 2011

Folding Step Stool - Free Plan

This is my take on a folding step stool design that's been around forever. My grandmothers each had one like it in their '50s kitchens. Today, fifty years later, you can point, click, and have a new one delivered to your door from any of a number of online vendors.

Many of these vendors describe their stools as "Amish". I'm not sure if that means the design is somehow Amish, or if the stools are being made by Amish builders, or what. In any case, they're pretty handy, and a heckuva lot safer than that upside-down Home Depot bucket you've been climbing on to reach the top shelf where Grandma keeps her gin.

Resources

If you want to build one of these yourself, the following two pictures link to drawings that give the basic dimensions for the stool:

The Stool
The Steps
Thanks to John Sprofera, you can also download a simple SketchUp model of the stool by clicking here.

There's also a more detailed SketchUp model here.  It shows the joinery in more detail, and has dimensioned drawings of all the individual parts.  This file contains the same set of drawings, but in PDF format if that's more convenient for you than SketchUp.

Construction Notes

I made my stool from oak, and finished it with several coats of wipe-on polyurethane. I used through mortise and tenon joints between the legs and the transverse stretchers, and floating tenons to join the legs with the side stretchers. I attached the seat and the steps with screws running up from underneath. These screws are set into oversize holes to allow the seat and the steps to expand and contract across their widths with changes in humidity. This precaution probably wasn't necessary for the steps because they are so narrow, but probably was for the seat.

Almost any wood would work for this project, although it might be a good idea to use a hardwood dowel for the step pivot, even if the rest was made from softwood. Likewise, any number of joinery options could work as well.

While there's nothing magical about this particular design, it is very important to get the shape of the side pieces that hold up the steps correct, as well as the location of the pivot pin. If you don't, the step assembly might hit one of the stretchers when it shouldn't. Be sure to keep this in mind if you decide to modify the plans for some reason.

The other thing to watch out for is the grain direction in the side pieces that hold up the steps. It's best to orient the grain as shown in the first picture above. Unfortunately, this makes it a little bit tricky to lay out the shape of these parts. To solve this problem, I made a full-size template out of 1/4" MDF. Then I traced around the template and cut out the parts slightly oversize with a band saw. Then I attached the template to the rough blanks one at a time and trimmed them to their final shape using a router with a flush trim bit.

40 comments:

Brett said...

Nice build and great pictures of the finished product. This seems like a truely useful and stylish piece. Thanks for sharing this and the dimensions too.

Anonymous said...

Great job. I like to copy.

Anonymous said...

I search all over the internet for picture of a folding step stool to copy but when I ran across your site and saw your plans I couldn't resist the invitation to use your easy to follow plan to build my folding step stool. I noticed was there was no detail pointing out the size to make the dowel hole. I just assumed it was 1". Other than that I enjoyed having you plan to build my project.
Thank you for the plan and nice work on your folding step stool!
AJ

rmac said...

@Anonymous: I think I used a 7/8" dowel on my stool, but 1" should be just fine, too. I'm glad you liked my plans.

-- Russ

Anonymous said...

It looks beautiful, great job. I'm heading out to get the oak now, the kids will love it in the bathroom. Thanks for the plans, I was dreading trying to lay this out from scratch.
Jeff

LCODD6 said...

HELLO,

Can you tell me the angles you used on the folding step?

rmac said...

LCODD6,

If you click on the second drawing, it should give you all the dimensions you need to lay out the folding step. So I am not sure what angles you have questions about. Please let me know and I will try to help you.

-- Russ

LCODD6 said...

I wish I could post a picture of what I"m talking about. I started to create a 3D model of the steps but something is off. The top step risers are at an angle, just wondering if you knew that angle. I've calculated 4.92 deg on the front and 3.81 on the back of the top step.

rmac said...

LCODD6,

Okay. I think I understand. I have updated the drawing to show the three oddball angles on the step. You may have to refresh your browser's cache to force it to grab the updated version of the drawing.

-- Russ

Aaron said...

Russ,
I made your stool today as a Christmas present for my mother in law. The stool turned out beautiful and saved me from designing something on my own. Thank you!

-Aaron

rmac said...

Hi Aaron,

You're welcome! Glad you like the stool and the plans.

-- Russ

Unknown said...

Thanks so much for sharing your plan. We saw on similar this weekend, and of course my wife wants one.

Anonymous said...

I've been looking for a step stool for awhile, this is the one. I'm building it out of walnut. Thanks very much for the plans... Joe Tee

Anonymous said...

Do you have a list of materials for this project?

Looks great!!

rmac said...

@Anonymous: The materials list is pretty simple. You need enough wood to make the parts shown in the plans, a handful of screws to hold the steps and the seat in place, and finishing materials (stain, polyurethane, whatever) of your choice. That's it!

-- Russ

Anonymous said...

Thank you for sharing your plans! You wrote that the seat and steps are connected by screws running up from underneath. Are those wood screws that run through cleats (with oversized holes) into the seat and steps?

Mark

rmac said...

@Anonymous: You got it! Try this link to see another guy's stool built from these plans. The last of his six pictures shows the cleats more clearly than mine do.

Robert M said...

Wow - I saw a stool like this some 30 years ago. I always wanted to build one. Sure do appreciate your photos and dimensional drawings - but I'm a bit intimidated by those angles on the stairs.

Should I be?

rmac said...

Don't let the angles on the drawing of the stairs scare you. They're there mostly just for reference. If you lay out the location of the pivot pin and all the corners of the parts according to the dimensions given, the goofy angles will all take care of themselves.

However, you do need to pay attention to the angle shown on the other drawing so you know what angle to cut the ends of the legs and stretchers at. But that angle is just an even 10 degrees in every case, so that shouldn't be too scary.

Quite a few people have built stools from these plans, so it's definitely possible. Just go for it!

Unknown said...

So are the spacers on the dowel free floating spacers, or are they pinned in place? And does it matter?

rmac said...

Randy,

I left the spacers free floating. There's no reason to pin them, and drilling a hole in the dowel would only weaken it.

Richard said...

I was wondering whether the dowel was fixed/glued to the folding sides or to the 2" legs of the frame, which one allows the dowel to slip? Thanks

rmac said...

I don't think it really matters, but you have to think about how you are going to assemble the stool. For example, if you glued the dowel into the folding sides first, you might have a heck of a time assembling the frame around it.

On mine, the dowel is a press fit in the holes in the 2" legs, and a loose fit in the holes in the folding sides. So when you fold the steps up and down, the dowel does not rotate. With that arrangement, I was able to build the frame and the steps separately, then just thread the dowel through all four holes as the final assembly step.

I got lucky with the "press fit" part, and didn't need anything besides friction to hold the dowel in place. My plan had I not been so lucky was to pin the big dowel in place with a smaller dowel in a hole in one of the legs.

John Sprofera said...

This will be a nice build for me. Thanks for sharing. If you would be interested I have drawn your plans on Sketchup for anyone to see it in 3d with your permission. Would make it nice to have to print out for a 3D shop plan to view

rmac said...

John, thank you for the SketchUp model of the stool. I have posted it online and added a link to the file in the body of the article.

Anonymous said...

You made the steps as a single board. How wide was the stock you used. I'm not mathing well today and am having a bit of an issue figuring it out

rmac said...

According to the CAD model, the minimum size for the boards on the sides of the steps is 8-5/8" wide by 17-1/2" long. Of course you'd probably want a little extra in both dimensions to start with.

Click here to see exactly what I'm talking about.

If I remember correctly, I didn't have stock that wide when I made my stool, and edge glued some narrower boards together to get the required width. Best of luck with your project.

Unknown said...

bn

Anonymous said...

Just made one, following the dimensions for height (I used 8 quarter Hickory) and it worked out great. Only thing I'll change on the next one is the steps. I'll make them 1" longer to bring the center of balance out. If you step on the back side of the top step it can try to flip in. I made spacers for the dowel 1" and it worked perfectly. The other change is I used pocket screws, it was my wife's Christmas present I started on Christmas eve and had to be done in one day. I love mortise and tenon joints but didn't have time to hand chisel them. Thanks for the great sketches and dimensions.

Rick VanNorman said...

Hi,
I just stumbled onto this post, and I'll be building one for my wife who is vertically challenged!
My question is more about the actual Sketchup file you provide: How do you get the "constant size frame" for the various scene renderings? It's the best hack for Sketchup I've seen, and I can benefit greatly from the technique. Please explain!
Thanks,
rick

rmac said...

Hi Rick,

Basically you make an image of whatever border you want, then add it to your Sketchup model as a watermark. There's a more complete explanation here.

-- Russ

Rick VanNorman said...

Many thanks! For the explanation and the design!

rick

Serkan Kaya said...

Hello. I made your project in the same dimensions. It was very nice. Thank you for your sharing.

Greg Crawford said...

Hi. I just finished your step stool in walnut. I used my pantograph router (See Mathias Wandel, Woodgears.ca) to cut mortise and tenons. I used 1" stock, because I got tired of running it through the planer. As a result, my mortises are all blind holes instead of through tenons. But it seems very stout. My tenon pattern on my router cuts 3/8" x 1-1/16" tenons. Anyway, I will start putting on the finish tomorrow. This is a Christmas present for my wife. She currently uses a regular stool, and climbs up the rungs. This should be much safer. Thank you so much for making these plans available to the public.

rmac said...

Greg, glad you like the plans. If you look back through these comments, you'll see that one guy built one of these on Christmas Eve as a gift for his wife the very next day! He's a braver man that me.

Greg Crawford said...

He's braver than me too! Plus, I can't work that fast! Mine's looking really good, I've got one coat of General Finishes satin urethane on it with two more to go. I may put some marine non-skid powder on the steps, as they are a little slick. Thanks again, and Merry Christmas to you.

Mauro said...

Execelente trabalho, bonito, pratico e util.
Talves um projeto para o futuro,
Agredeço por compartilhar sua ideia.

rmac said...

Obrigado!

Unknown said...

I have a bunch of leftover 1" oak dowels. I was thinking of using these instead of the mortise and tenon spacers and such. Once I'm finished the project I will share with all.

Unknown said...

Finished the project with oak dowels. Very strong and stable and I think lighter than the version with mortice and tenons. I'm not sure how to post a picture to the blog however.

Post a Comment